Service parts for your valve
Genuine manufacturer parts for the five valve families in our manual library — every part under the number printed in the factory service manual, with what it does and the symptom that points to it. Priced parts are priced just above wholesale and can be ordered right here; the rest we order in for you with one call.
How ordering works
- Find your valve. The family name is on the valve label — Clack WS1, Fleck 5600, Autotrol 255, Hankscraft REV 2.5 or REV4. Each family's owner's guide is linked from its parts list below.
- Match the part number. Parts are listed under the manufacturer's own numbers, straight from the factory service manuals. Not sure which part your symptom means? Call (727) 342-0091 with what the valve is doing and we'll match it before you spend anything.
- Order. Priced parts check out online. Call-to-order parts are ordered in under the exact number — no substitutes.
- Shipping, plainly: online prices are for the part itself — shipping isn't built into them yet. If a part has to be mailed to you, we'll email you after checkout to arrange delivery or a local pickup in the Tampa Bay area before anything ships. Nothing extra is charged without your say-so.
Clack WS1 & WS1.25
The WS1 wears in a predictable order: the seal stack and the pistons do the sliding, so they do the wearing. Everything below is straight out of Clack's own drawings and service manual, under Clack's own part numbers. Silicone lubricant only on anything rubber in this valve — petroleum products damage the seals. Owner's guide: Clack WS1 & WS1.25 quick guide.
See the parts list — 13 parts, with prices & ordering
| Part | What it does | The symptom that points to it | Price |
|---|---|---|---|
| Spacer Stack AssemblyV3005-02 | The seal cage: a one-piece stack of seals and spacers — Clack's patented design — that the piston slides through. It keeps service water, brine, and drain water in their own lanes. | Hard water slipping through, water running to the drain between cycles, or an internal leak. The manual's fix for all three: replace the seal/stack assembly. | $45.99Buy |
| Spacer Stack Assembly — WS1.25V3430-01 | The same seal-cage job, sized for the bigger WS1.25 valve body. | Same symptoms as the WS1 stack, on a 1.25-inch valve. | Call to order (727) 342-0091 |
| Piston, DownflowV3011 | The main piston. It moves to open and close the valve's ports for every step of regeneration. Stamped DN. | Water running to the drain, a cycle that won't finish, or a piston that no longer seats. Match DN vs. UP before ordering — they are not interchangeable. | $13.99Buy |
| Piston, UpflowV3011-01 | The upflow version of the main piston, stamped UP. (Upflow doesn't apply to TC timer valves.) | Same failure signs as the downflow piston, on an upflow-programmed valve. | $37.99Buy |
| Regenerant PistonV3174 | The smaller second piston that works the brine (regenerant) side of the cycle. | The valve runs its cycle but won't draw brine out of the salt tank — the manual names a faulty regenerant piston. | $8.99Buy |
| Injector AssemblyV3010-1A through V3010-1K | Creates the suction that pulls brine into the valve. The letter is the size, and it has to match your tank diameter — call and we'll match it. | No brine draw, salty-tasting water, or a brine tank that keeps gaining water. The manual's first move is clean it; replace it if cleaning doesn't restore draw. | Call to order (727) 342-0091 |
| Injector Screen & CageV3177-01 screen cage · V3176 injector cap | The screen keeps debris out of the injector; the cage and cap hold it in place under the injector cap. | Brine draw that fades or stops — a plugged screen starves the injector before anything else fails. | Call to order (727) 342-0091 |
| Drain Line Flow Control (DLFC)V3162 series for 3/4-inch drain, 0.7–10.0 gpm | A sized button that sets how fast the valve backwashes. One must be fitted whenever the 3/4-inch drain fitting is used. | Resin blowing out to the drain (too fast) or a bed that never gets clean (too slow). Sized to the tank — call to match. | Call to order (727) 342-0091 |
| Refill Flow Control AssemblyV3165-01, with V3182 refill control (0.5 gpm) | Meters the water that refills the brine tank after regeneration. | Too much or too little water standing in the brine tank — the manual lists a plugged or missing refill flow control for both. | Call to order (727) 342-0091 |
| Meter Turbine AssemblyV3118-01 (in meter assembly V3003) | Counts gallons so a demand valve knows when it's time to regenerate. | The display doesn't show water flowing, or the valve never regenerates on its own but will from the button. Check the turbine for debris first. | Call to order (727) 342-0091 |
| Drive Cap AssemblyV3004 | Caps the drive end of the valve and carries the drive gear that moves the piston. | The valve won't regenerate when the button is held — the manual names a broken drive gear or drive cap assembly. | Call to order (727) 342-0091 |
| Bypass ValveV3006 | The red-handle block on the back of the valve that cuts the softener out of the line for service. | Hard water at the tap with the valve in service — a bypass left open, or one leaking past its seals. | $37.99Buy |
| Valve Body & Distributor O-RingsV3135 (O-ring 228) · V3180 (O-ring 337) · V3105 (O-ring 215) | The main body seals and the distributor-tube O-ring. Silicone lubricant only on Clack seals — petroleum products damage them. | Weeping at the valve body or tank connection after a rebuild, or a distributor tube that won't seal. | Call to order (727) 342-0091 |
Fleck 5600 & 5600SXT
Pentair publishes a maintenance plan for this valve, and it's honest about what wears: the piston and the seals & spacers are wear parts — checked yearly, replaced on about a 3-year cycle, and sooner when the water carries chlorine, which eats the rubber. Every number below is from Pentair's 5600 service manual and the 5600SXT installer manual. Owner's guide: Fleck 5600 & 5600SXT quick guide.
See the parts list — 9 parts, with prices & ordering
| Part | What it does | The symptom that points to it | Price |
|---|---|---|---|
| Seals & Spacers KitKit 60125 · Pentair S&S kit 24115 (seals 13242, spacers 14241) | Five seals and four spacers that the piston slides through — the wear heart of the 5600. This is the kit Pentair's own maintenance plan is built around. | Drain flowing when it shouldn't, internal leaks, hard water creeping back. Pentair's plan: check yearly and replace on about a 3-year cycle — chlorine in the water shortens their life. | $26.99Buy |
| Piston Assembly — softener60102-00 (valve piston 13247 · SXT list 24116-US) | The main piston that routes water for service and every regeneration step on the mechanical 5600. | Drain flows continuously, the valve jams in brine or backwash, or an internal control leak — the manual's answer is seals and/or the piston assembly. | $54.99Buy |
| Piston Assembly — 5600SXT downflow60102-71 (SXT list 27077-US) | The piston for the electronic SXT head in downflow service. | Same drain-flow and leak symptoms, on an SXT-equipped valve. Confirm downflow before ordering. | Call to order (727) 342-0091 |
| Brine Valve60032 | The brine valve assembly that starts and stops brine draw and refill. | Brine tank overfilling, no brine draw, or brine in the house lines. Pentair's plan checks it yearly and replaces it on the 5-year mark. | $17.99Buy |
| Injector Service Kit29115 · injector assemblies 29109–29114 by size | Services the injector nozzle, throat, and screen (manual parts 10913U, 10914, 10227) — the parts that make brine suction. | Weak or no brine draw; the unit using too much or too little salt. Pentair's plan: clean yearly, replace if cleaning stops working. | Call to order (727) 342-0091 |
| SXT Service Kit29108 | Pentair's bundled 4600/5600 SXT service kit for the electronic-head valves. | A general refresh on an SXT valve that's due its 3-year piston and seal service. | Call to order (727) 342-0091 |
| Tank Adapter O-Ring Kit29101 | The O-rings where the valve body meets the tank adapter. | A leak at the base of the valve, where it screws onto the tank. | Call to order (727) 342-0091 |
| End Plug Retainer Kit29100 | Retains the piston end plug at the back of the valve. | An end plug that weeps or works loose. | Call to order (727) 342-0091 |
| Brine & Drain Flow Control ButtonsBLFC 12094 (0.25 gpm) · 12095 (0.50) · 12097 (1.0) · DLFC button with retainer 13173 | The little buttons that set brine refill speed (BLFC) and backwash speed (DLFC). | Brine tank level wrong (BLFC) or backwash too weak or too strong (DLFC). Pentair's plan: clean them yearly before replacing. | Call to order (727) 342-0091 |
Autotrol 255 & Performa (742 / 762 Logix)
No piston, no seal stack — a camshaft lifts flapper discs, so the flappers are the wear part on this valve. The numbers below are from Pentair's Autotrol 255 & Performa service manual. Owner's guide: Autotrol 255 & Performa (742 / 762 Logix) quick guide.
See the parts list — 10 parts, with prices & ordering
| Part | What it does | The symptom that points to it | Price |
|---|---|---|---|
| Valve Disk Kit — the flappers1000250 | The full set of flapper discs the camshaft lifts to route water. On this valve the flappers ARE the seals — there is no piston and no seal stack. | A drain line that drips all day, hard water getting past, or a valve that won't hold a cycle. Worn flappers are the first suspect — Pentair's service book treats the disk kit as this valve's wear part. | $43.99Buy |
| Camshaft — 255, standard1235353 | The shaft whose lobes lift the flappers in sequence through the cycle. | Err 3 on the display, or the valve stuck mid-cycle. Pentair's rule: a broken or damaged camshaft is replaced, never repaired or modified. | Call to order (727) 342-0091 |
| O-Ring Kit — Tank Adapter1001404 | The O-ring set for the tank adapter connection. | A leak where the valve meets the tank. | $7.99Buy |
| O-Ring Kit — Piping Boss1040459 | The O-ring set for the piping boss (manifold) connections. | Weeping at the inlet/outlet manifold connections. | $4.99Buy |
| Injectors, sized E through L1035730–1035736 · injector cap with O-ring 1000269 | Create the suction that draws brine. The letter matches your tank size — call and we'll match it. | Weak or no brine draw, or draw that quits early. | Call to order (727) 342-0091 |
| Drain Control Assembly1000209–1000215 (sizes No. 7–14) | The sized assembly that sets the backwash rate. | Backwash too weak to lift the bed, or strong enough to push resin to the drain. | Call to order (727) 342-0091 |
| Regenerant Refill Controller1000222 (0.33 gpm, no ball) · 1243510 | Sets how much water goes back into the brine tank after regeneration. | Brine tank level too high or too low after every cycle. | Call to order (727) 342-0091 |
| Air Check Kit1032416 (3/8-inch) · 1032417 (1/4-inch) | Keeps air out of the brine line when draw ends. | Brine draw that stops early, or air getting pulled into the valve from the brine line. | Call to order (727) 342-0091 |
| One-Piece Spring1235341 | The spring that holds the valve discs seated against the camshaft. | Seepage past flappers that are still in good shape. | Call to order (727) 342-0091 |
| Service Kits — motor & optical sensor1239711 / 1239752 front mount · 1239753 / 1239754 top plate mount · sensor module 1235373 | The drive motor and cam-position sensor service kits for the Logix controls. | Error codes, a camshaft that doesn't turn, or a control that can't tell where the cam is. | Call to order (727) 342-0091 |
Hankscraft REV 2.5
Ceramic discs instead of a piston, so the wear list is short. Hankscraft's manual is direct that replacement parts should come through its resellers — which is why every part here is call-to-order, under the exact numbers from the RevV2.5 service manual's own parts list. Owner's guide: Hankscraft REV 2.5 quick guide.
See the parts list — 10 parts, with prices & ordering
| Part | What it does | The symptom that points to it | Price |
|---|---|---|---|
| Moving Disc8459078 | Half of the ceramic disc pair that routes the water. This valve has no piston and no rubber seal stack — the discs are the valve. | Water flowing from the drain or brine line after regeneration. The manual's correction: change the valve core or the sealing ring. | Call to order (727) 342-0091 |
| Fixed Disc8469079 | The stationary ceramic half the moving disc turns against. | Replaced with the moving disc when the pair is scored or worn — the two are a matched sealing surface. | Call to order (727) 342-0091 |
| Moving Seal Ring8370001 | The seal ring that rides with the moving disc. | Internal leaking past the disc pair with discs that still look clean. | Call to order (727) 342-0091 |
| Seal Rings — body set8216004 · 8371001 · 8370012 · 8371003 | The body and cover seal rings from the manual's parts list. | Weeping at the valve body joints or cover. | Call to order (727) 342-0091 |
| Injector Nozzle & Throat8454009 nozzle · 8467009 throat · 8008010 injector body | The pair that makes brine suction at the injector body. | The softener fails to draw brine — the manual's fix is clean or replace the injector. | Call to order (727) 342-0091 |
| Drain Line Flow Control8438054 | Sets the backwash and rinse flow to drain. | Too much water in the brine tank or poor rinsing — the manual names a plugged DLFC; clean first, replace if damaged. | Call to order (727) 342-0091 |
| Brine Line Flow Control8468055 | Sets the brine refill rate into the brine tank. | Brine tank level wrong, or the unit using too much salt. | Call to order (727) 342-0091 |
| Flow Meter5447018 | Counts water use so the metered modes (A-01/A-02) know when to regenerate. | Capacity dropping or regeneration coming at the wrong time — the manual: disassemble and clean the meter, or replace it. | Call to order (727) 342-0091 |
| Motor6158073 | The drive motor that turns the disc through its cycles. | The softener fails to regenerate and the controller checks out — the manual's correction is replace the motor. | Call to order (727) 342-0091 |
| O-Rings — tank & body8378143 (73×5.3) · 8378078 (25.8×2.65) · 8378128 (73×3.55) · 8378184 (38.7×3.55) | The riser-pipe and body O-rings from the parts list. | Hard water from a leak at the riser-pipe O-ring, or weeping at the tank connection — the manual's hard-water checklist starts here. | Call to order (727) 342-0091 |
Hankscraft REV4
Hankscraft doesn't publish a homeowner parts list for the REV4, and the ceramic internals carry a lifetime guarantee — so this list is short on purpose. Parts are ordered by model and serial through Aqua Pro. Owner's guide: Hankscraft REV4 quick guide.
See the parts list — 3 parts, with prices & ordering
| Part | What it does | The symptom that points to it | Price |
|---|---|---|---|
| Ceramic Disc SetHankscraft patented ceramic internals — ordered by valve model | The matched ceramic discs that route the water. Hankscraft's catalog puts a lifetime guarantee on the ceramic internals — corrosion and abrasion are what they're built to shrug off. | Honestly: this is the part that almost never wears out, and that's the point of the design. If a REV4 leaks internally, call first — diagnosis comes before parts on this valve. | Call to order (727) 342-0091 |
| Ceramic Bypass41206 / 41207 | The bypass documented in the REV4 manual (§6) — the same ceramic bypass family the REV 2.5 uses. | Hard water with the valve in service, or a bypass that won't turn or won't seal. | Call to order (727) 342-0091 |
| Everything else on a REV4Ordered by model and serial number | Hankscraft doesn't publish a homeowner parts list for the REV4 the way the other makers do, and its manual directs parts through its resellers. Give us the model and serial off the valve and we'll order the exact part in. | Any REV4 fault beyond the bypass — start with a call and the numbers off your valve label. | Call to order (727) 342-0091 |
Not sure which part you need?
That's normal — the same symptom can have two causes, and the manuals themselves work symptom-first. Describe what the valve is doing on a call and you'll get the part that matches, or a straight answer that it isn't a parts problem. If you'd rather it was diagnosed at the unit, that's the $149 service call. And if the valve is misbehaving right now, start with Softener Emergency Help — bypass first, parts second.
Part numbers and wear guidance on this page come from the manufacturers' own books: the Clack WS1 & WS1.25 Drawings and Service Manual, Pentair's Fleck 5600 Service Manual and 5600SXT Installer Manual, Pentair's Autotrol 742/762 (255 & Performa) Service Manual, and Hankscraft's RevV2.5 Service Manual and product catalog. Free copies of the manuals are linked from each valve's guide page.
Pinellas County, FL